Confidently test samples to the composition and performance standards you require. What’s more, a range of complementary services helps to keep your laboratory up and running smoothly. The dart impact test is the most common testing procedure utilized for evaluating impact strength. A weighted round-headed dart is released onto a tightly clamped sheet of film, and the sample is examined for failures visually. Since dart impact is not evaluated in any film direction, it is sensitive to orientation effects in both directions. Measure the sliding resistance of sheet materials including plastic film, packaging film laminates, paper, paperboard. Tear testing measures the force required to continue the tearing of an initial cut in sheet materials. Models and weights are available to test material with a variety of strengths.
FIT-01 can be used to determine impact resistance properties of pendulum of plastic films, sheets, composite films, aluminum foils and other materials in accordance with ASTM D3420. C640 Thickness Tester is a high precision mechanical contact method thickness tester, which can be used for thickness measurement of films, sheeting, paper, corrugated paperboard, textiles, non-woven fabrics, and solid insulation materials, etc. In case of testing vacuum leakage, the container, with the product is put in a vacuum sealed chamber and the pressure inside the chamber is dropped. If improperly manufactured, the walls of the packaging or the region of the seal will begin to leak. The slant leakage test checks different orientations of the package for leakage. Leakage tests allow manufacturers to see if the container can hold the product under different pressures or under different orientation. It is one of the important considerations in packaging material testing methods.
Our scientists are plastic detectives, capable of analyzing plastics in a wide variety of ways with careful documentation, continuous communication, and proper certification. Plastics are part of everything we do, from the cars we drive to the utensils we use to eat meals in those cars; from the cables wrapping our electrical wires to the pipes bringing water to our faucets. It’s crucial to predict how plastics will behave under a wide variety of circumstances, and to discover why plastics fail when they do. Submit your e-mail address and get instant free subscription to our weekly newsletter with industry updates, news and latest services offered by us. They are aware of the repercussions of poor packaging on the products they consume and how it impacts the environment and their health at large. For communities with best practices and scalable systems, Graff said, “loose automated collection of the material is the way to go.” There was extensive debate, years ago, in the solid waste and recycling collection end of the business about whether single-stream or dual stream recycling was more advantageous.
For more information on how Labthink can help your company profit through testing, please Click the button. C681M Flex Durability Tester is professionally applicable to the determination of flex durability of flexible films, composite films and coating films. In flip top caps, common with ketchup bottles, the flip top opening force determines how much force is needed to open the cap. If the flip top opening force is too high, then opening the cap will also break the hinge. Transit tests check how much stress the packaging can endure while it is being shipped in bundles. The packaging is subjected to different types of stresses when it is out on the road, being transported from point A to B. These stresses are much different from those that the packaging will face in retail stores or when it is with the end user. Transit tests check how many drops, how much inclination or vibration the packaging can endure. Overfill capacity is the capacity of the bottle or jar when filled up to the brim. This allows the manufacturers to determine if certain types of products will fill in certain types of bottles.
Helium leak detection is widely used for applications that require utmost leak sensitivity. A linear scan analysis of the seal area can be produced in seconds using PTI’s Seal-Scan® or Seal-Sensor™ technology. PTI is committed to our R & D to build a powerful array of leading edge technologies, bringing patented and unique solutions to high risk packaging applications. Formally confirming that your products and services meet all trusted external and internal standards. Validating the specifications, value and safety of your raw materials, products and assets. Used to execute the tension, compression, bending, flexural of metal and non-metallic materials under high toughness and hardness against extreme big loading force. C206H Oxygen Transmission Rate Test System is designed and manufactured based on the coulometricsensor method and conforms to ASTM D3985. C201B Oxygen Transmission Rate Test System is designed and manufactured based on the coulometric sensor method andconforms to ASTM D3985. C360 Water Vapor Transmission Rate Test System, is designed and manufactured based on the gravimetric determination method and conforms to the requirements of ASTM E96. TQD-G1 is professionally applicable to the determination of air permeability of decorating materials used in cars, e.g. polyurethane, expanded plastics, PVC, leather, textiles, non-woven and other materials.
COF Inclined Plane Tester Measure the static coefficient of friction of various materials using a variable inclined plane and a sliding block. FT-F1 Fogging tester to to test for fogging on upholstery material and time frame for testing. GBPI is a professional manufacturer focused on developing and producing packaging material test instruments. Oxygen and Water Vapour Transmission testing – OTR and WVTR or MVTR gives you the data you need to best control the shelf life of your product. A variety of factors can effect the coefficient of friction tester measurements including abrasion, coatings, varnishes, printing and most importantly humidity. We are passionate in what we do, in striving for excellence in customers service, product quality and on-time delivery.
Often the package is conditioned to the specified environment and tested under those conditions. With some testing, the package is conditioned to a specified environment, then is removed to ambient conditions and quickly tested. With some types of packaging such as food and pharmaceuticals, chemical tests are conducted to determine suitability of food contact materials. Testing programs range from simple tests with little replication to more thorough experimental designs. PET containers have numerous points of interest over different structures, similar to, glass. These are a portion of the regular advantages of utilizing a PET, yet the greatest preferred standpoint is that it is anything but difficult to re-evaluate the plan of plastic pressing in the event that it is bombing over and again. The revaluation procedure does not cost the fortune to the organization but rather unquestionably requires a correct testing process.
These plastic standards allow plastic manufacturers and end-users to examine and evaluate their material or product of concern to ensure quality and acceptability towards safe utilization. At Atlantic, we specify high quality, high performance films that are engineered with ultimate load holding force and are also very consistent . Because of the testing we perform in the Film Lab, we can illustrate these film properties with data. With our specialized stretch film testing equipment, we participate in the development of new stretch films, working not only with film manufacturers but also with the producers of the resins used to fabricate stretch films. The ASTM D638 standard is defined as a testing method to determine the tensile strength of both reinforced and non-reinforced plastics. This protocol is performed on “dog bone” shaped samples and under different pre-treatment, temperature and humidity conditions as per the different speeds of the testing machine. Hot tack strength (the force to measure seal-strength while the film is still semi-molten) is too low, the film will not perform or run properly during the filling operation and the package may leak product after it is filled.
For many clients, the sample that is submitted is the actual product or the portion of the product that contains the plastic. Testing food packaging to make sure it doesn’t contaminate food or break down when frozen or microwaved — but will break down in a landfill. The right packaging also needs to ensure the safe delivery of the product through the supply chain. We report news, gather data and deliver timely information that provides our readers with a competitive advantage. But it is not uncommon for MRF operators to have to shut down their lines completely several times each day to allow workers to go into the machinery and cut out flexible plastics have wound themselves around sortation equipment. While collection programs differ significantly from location to location, most customers have long been able to put in their recycled PET and high density polyethylene containers into curbside mix.
However, a significant investment in molecular and morphological design, mechanical and physical property testing and product evaluation is necessary before new materials can be introduced into these applications. At ST Instruments we provide surface measurement equipment to accelerate your research in the field of polymers and plastics. Hear an overview of the packaging industry’s analytical requirements with a focus on the accurate testing of flexible, rigid and multi-layer plastics, including compliance with essential international safety & quality regulations and standards. This video will give you insight on how Covid-19 affects and will continue to affect the industry. It will further explain how these issues are interconnected with the path to greater sustainability and recycling. Test instruments for the repeatable measurement of thickness, friction and shrink properties of plastic film. Chemical testing of a plastic or polymer material can be complex but can provide valuable information on the additives used and other substances present which is important when trying to understand material performance. Additives, in particular, can impact the polymer physical properties, stability / stabilization and general durability over the lifecycle of the polymer material. Other substances present include catalyst residues and volatile organic contaminants .
This packaging testing equipment is used for testing materials such as boxes, cartons, glass, and ceramic. Packaging testing equipment is expected to gain traction in food and beverages industry. The key objectives of food and beverages industry is to ensure longer shelf life of products for avoiding the loss of revenue generation. Also, demand for packaged food is increasing which is increasing production of food and beverages and ultimately driving the growth of packaging testing equipment. Moreover, the environmental factors such as humidity, sunlight, and temperature easily affects the product quality when it comes in direct contact and packaging acts as insulation for these products. This parameter is accelerating the adoption of packaging testing equipment in healthcare and pharmaceutical industry. Our CNAS and ISO 9001 certified company is serving testing equipment of standard configurations in printing, packaging, pharmaceutical and other industries. We have a capable R&D team to meet special request of customers by designing and developing customized equipment for application specific use.
Due to all these facts, it becomes important for the manufacturers to ensure that the packaging products that are being used for the packaging purposes are best in terms of quality. Labthink providesLeak Test Equipment for Plastic PET Bottlesof food, drugs, medical instruments, daily chemical products, cars, electronic components, stationeries and other industrial products. This test solution employs a MultiTest-i system, which is controlled via a PC. The software enables a graphical representation of the test to be plotted on screen, with automatic calculation of static and kinetic coefficients of friction. This provides further data regarding the materials surface structure and frictional properties including ‘stiction’ . A coefficient of friction test identifies the frictional values of materials and how different material surfaces relate to one another. For example, if the coefficient if too high, the material cannot be fed through all the machinery efficiently, causing misfeeds. Plastic packaging systems can include—not only the container that holds a particular drug product—but also gaskets, rubber stoppers, tubing and other components that may be part of the overall system used to store and/or deliver a drug to the patient. Rose Plastic’s bespoke solutions are available in a range of foam densities with a wide selection of colours and designs. With CAD/CAM design, multi-axis machining, die-stamp and waterjet cutting, rose plastic offers affordable protective inserts that can accommodate complex shapes and depths to offer a custom solution for your needs.
Food packaging favors films that are as thin and durable as possible, but yet protect foods safely. Thermocell has already been shown to provide good protection against water vapor, and none of its components migrate into the food. Thermocell film can also be heat sealed using the manufacturers’ standard equipment. VTT is testing Thermocell plastic film made of cellulose and fatty acids in the production of food packaging in cooperation with Arla Foods, Paulig, and Wipak. Thermocell plastic material, which is made from renewable components, is to be used in the same way as fossil-based plastic. Thanks to the development work, many features of the film already meet the requirements of the food industry, and cooperation has advanced to the testing of industrial production. packaging material testing lab/laboratory and professional team of scientists are experts in testing food packaging materials. We have a comprehensive range of equipments and our testing services include national & international methods for the evaluation of food packaging materials.